• Search Title Only

22 Results for Metal Lathe Craftsman in Minneapolis Mn - Classifieds

10
$30

For sale is a 10" Craftsman contractor style table saw. It has a cast iron top, fence, miter gauge, sheet metal side extension wings and built in retractable casters. It also comes with a brand new dado blade insert…

1 month ago on SpreadMyAd
HEAVY 10  10L SOUTH BEND METAL LATHE HEADSTOCK SPINDLE
$90

Here's a nice spindle for a SOUTH BEND Heavy 10L. 2-1/4 x 8 threads are near perfect as is the taper bore. Thrust but threads are in great shape. There is a tiny bit of wear on the large bearing surface but no scori…

1 month ago on ebay.com
HEAVY 10 SOUTH BEND METAL LATHE ORIGINAL MOTOR PULLEY 2130 NR1
$50

Good original heavy 10 motor pulley. It has a 3/4" bore with a 3/16" keyway. The large pulley has an outside diameter 3.395 and the small pulley 2.093. Top of the 'V' is .635 wide. Does have some light rust, but sho…

1 month ago on ebay.com
HEAVY 10  10L SOUTH BEND METAL LATHE HEADSTOCK SPINDLE SLEEVE BEARINGS
$115

Both front and rear bearings are in great shape. The rear one looks new inside and the front one has a few very small scratches, but these usually don't cause any problems in the lathes I have used them in. The small…

1 month ago on ebay.com
HEAVY 10 SOUTH BEND METAL LATHE 80T IDLER GEAR 33R1
$60

Here is a nice 80 tooth idler gear for a South Bend heavy 10. Overall it's in good condition. There are not chipped or cracked teeth. I cannot see any visible wear, but due to age I'm sure it has a little. Overall a…

1 month ago on ebay.com
BACK GEAR AND ECCENTRIC FOR A 9
$110

Here is a very nice back gear assembly for a South Bend 9 or 10K lathe. Overall this is in very nice condition. All of the teeth are in very good shape with no cracked or chipped teeth. There are no visible signs of…

1 month ago on ebay.com
Fox Run Gingerbread House Metal Cookie Cutter, Craftsman 3608, 1986, NIB
$13

Fox Run Craftsman Holiday Cookie Cutter - Gingerbread House Metal - 7-1/2" with handle Dated 1986, #3608Cutter is in great shape, never used, and the box is also in good shape with some shelf wear on box tabs.…

1 month ago on ebay.com
Fox Run Christmas Santa Metal Cookie Cutter, Craftsman 3610, 1992, NIB
$13

Fox Run Craftsman Holiday Cookie Cutter - Santa Metal - 7-1/2" with handle Dated 1992, #36010Cutter is in great shape, never used, and the box is also in great shape with just a few places where tape or tags have been…

1 month ago on ebay.com
Fox Run 1987 Set of 6 Metal Holiday Cookie Cutters  Hanukkah Craftsman 3620
$13

Fox Run Craftsman Holiday Cookie Cutters Holiday (Hanukkah) Cookie Cutters, Metal, Set of 6 Dated 1987, #3620These cutters are in great shape, never used, but the box is a bit grubby and shelf worn from being stored in…

1 month ago on ebay.com
CRAFTSMAN 113 SERIES TABLE SAW HAND WHEEL # 2
$145

HAND WHEEL # 2 from a early Craftsman, 10 inch belt drive table saw. Good condition item. Fits a 1/2" flat sided shaft. This is the upgraded wheel with the metal hex insert. It is not cracked. Saw #113.299040. Last…

1 month ago on ebay.com
Craftsman 4
$40

Craftsman 4" angle grinder with safety guard. Case. Metal brush. Two masonry cutting wheels. Three metal grinding wheels. One masonry grinding wheel.

1 month ago on ebay.com
[NO1] Dremel MM452 Multi-Max Bi-Metal Saw Blade
$10

precise cuts in wood and metal. Bi-Metal BiM construction is suitable for cutting finish nails and light metals in addition to wood, drywall, plaster and lath materials. Its offset design allows the blade to make flush cuts…

1 month ago on ebay.com
Antique Arts and Crafts Umbrella Stand with Metal Drip Pan
$99

.  The pyramid tops at the four corners gives it a nice look.  The red metal 8 inch in diameter drip pan is inset into the side rails - a really nice craftsman touch.   Oak wood.  Thanks for viewing and bidding.  Please check…

1 month ago on ebay.com
Drill Doctor 350X Drill Bit Sharpener Sharpens 3/32 To 1/2
$43

Doctor DD350X provides the homeowner, weekend craftsman or hobbyist with the sharpening power needed to restore dull bits and keep on working. The DD350X is an easy-to-use drill bit sharpener, ideal for the shop that uses the…

1 month ago on ebay.com
Evert Sodergren Knights Bench Midcentury Design Studio Furniture Rare!!
$2,200

Evert Sodergren Knights Bench. Made in 2000, design came from the mid century 50's. Sodergren was a studio craftsman from the Pacific Northwest who's works are in the collection of The Smithsonian, The Museum of Art and…

1 month ago on ebay.com
Results for Metal Lathe Craftsman in Minneapolis, MN